Homework Assignment 5 COP 3223C Sequence of Events Recorder

$30.00

Category:

Description

5/5 - (5 votes)

Description: Unexpected destructive failures of expensive equipment can be very frustrating to
designers and maintenance personnel because they don’t often have enough information to
allow them to determine what caused the failure. Because failures are almost always
unexpected, and typically result in complete loss of the device, doing a port-mortem analysis is
often difficult, leaving them to do no more than a visual inspection of the “corpse”. Examples
of these are the data black boxes in all commercial aircraft that record the last several minutes
of the critical variables of the aircraft’s operation just before the accident. Therefore, in failure
analysis, it is quite useful to know what the values of critical parameters were just prior to the
catastrophic failure. This is the purpose of a sequence-of-events recorder.
Sequence-of-events recorders are designed to capture the last few seconds, minutes, or hours
of the operation of the device of interest. They are generally located externally to the device to
avoid them being destroyed along with the device. Of course, this is not possible for aircraft
black boxes, so they make them almost indestructible instead. By recording only the last few
seconds/minutes/hours of operation, the memory requirements can be managed rather well,
especially when many variables are to be logged and/or they are to be sampled at a very high
rate of frequency. These recorders, therefore, will overwrite old data with new data, always
having in memory the critical last several seconds, minutes, or hours of the device’s operation
before the failure.
You work for a company that manufactures anti-lock braking systems for disk brakes for the
major automobile manufacturers. Recently, there have been several incidents in which the antilocking mechanism has failed, resulting in accidents on wet roads. While no one has yet been
injured, your company takes these incidents seriously and wants to resolve any issues before
anyone does get hurt. Nobody knows exactly how these devices have mis-operated, but several
of the drivers involved in such accidents have reported that the normal clack-clack-clacking of
the ABS brakes was replaced by a bing-bing-bing, at a much slower frequency. The engineers
are baffled as to what might have caused that, but they do know it isn’t normal.
So, you have been assigned to design a sequence-of-events recorder to capture the last 10
seconds of operation of the car. There are several sequence-of-events recorders on the market,
but none are specially suited to your high frequency application. So, you have to write the code
yourself. Your program is to acquire the values of several variables during one time (called a
slice of data) and save them to circular array of structures that saves the last 10 seconds of data
acquired. The sampling frequency has been specified by the design engineers to be 10 Hertz
(10 data slices per second), as auto accidents only take a few seconds to happen.
The system should repeatedly acquire the values of the following variables during the
operation:
1) Brake fluid pressure to the brake unit: between 20 and 30 PSI.
2) Electrical power to the braking unit: between 10 and 100 watts.
3) Driver brake pressure (applied by the driver): between 30 and 40 PSI.
4) Pressure applied to the disk: 10 to 15 PSI.
5) Time in seconds.
Specifically, your assignment is to design and write a program that captures the time-tagged
data slices of the variables above and saves them to a circular array of structures. Use a
sampling frequency of 10 Hertz. Circular arrays overwrite the oldest slice of data with the
newest, thereby keeping the last several slices leading up to the accident, which is what you
want to do. When an accident occurs (or the car is turned off), the program writes the last
several slices of data to an external file. Because you’ll only be testing the system for the
purposes of this assignment, you can create the values using a random number generator. Save
these values to an array of structures that contain a member for each one of the stored
variables, plus one more for the time. The time can be assumed to be sequential, starting from
0 and going until the car is turned off normally through the operation of the key … or it crashes.
The array is to contain the last 10 seconds’ worth of data (100 data slices). Then, write a
second program (separate from the one above) that reads the external file and prints it to
screen. The output to screen should look something like this:
Time
(secs)
Brake fluid
pressure
Pressure
on disks
Driver brake
pressure
Electrical Power to
unit
.1 25 15 32 70
.2 20 10 33 72
.3 21 11 32 71
.4 23 10 30 75
.5 24 12 33 78
.6 21 10 36 70
.7 23 12 34 75
.8 22 11 38 78
.9 25 13 35 73
1.0 24 15 32 72
1.1 23 12 31 80
1.2 25 16 33 73
1.3 27 17 36 69
Where it prints the entire 10 second run of the values of each of the variables, at each 0.1
second.
Notes
1. You must use the following elements in the program:
a. A struct structure
b. An array of size 100.
c. A random number generator (rand())
d. At least two user-defined functions
e. The typedef data specifier for the structure.
2. Put the data acquisition process in a for loop with exactly 1177 cycles. Assume that
when it ends, the car crashed or the driver got to his/her destination and turned the
engine off. Use that as the signal to write the collected data to the file.
3. Use integers for the values of the variables, even though floating point values would be
much more realistic in this application. It’s much easier than generating floating point
numbers.
4. Record the time in intervals of 0.1 seconds.
5. Comment your file adequately. Indent and space adequately.